if (client) { // if you get a client, #ifdef DEBUG Serial.println("New Client."); // print a message out the serial port #endif
String currentLine = ""; // make a String to hold incoming data from the client while (client.connected()) { // loop while the client's connected if (client.available()) { // if there's bytes to read from the client, char c = client.read(); // read a byte, then
#ifdef DEBUG Serial.write(c); // print it out the serial monitor #endif 0505774ワット発電中さん2018/11/16(金) 18:22:48.80ID:mTmlEb3v アクセス回数カウントしてみて? 0506774ワット発電中さん2018/11/16(金) 18:24:39.35ID:mTmlEb3v あとchip Rev.が知りたいかな 0507774ワット発電中さん2018/11/16(金) 18:35:05.22ID:UpzDESQt>>506 秋月から購入のDev0開発キット。 Dev1キットは未購入 0508774ワット発電中さん2018/11/16(金) 19:41:12.34ID:jDk6l8Fk ガベージコレクション発生しないようにいたわってやれよ 0509774ワット発電中さん2018/11/16(金) 19:50:25.67ID:UpzDESQt>>508 ん? String currentLineのようにスタックに切るなという事? 0510774ワット発電中さん2018/11/16(金) 20:28:00.27ID:UpzDESQt>>505 19028回ですた。
if (client) { // if you get a client, #ifdef DEBUG Serial.println("New Client."); // print a message out the serial port static long accesscount = 0; Serial.println(++accesscount); #endif 0511774ワット発電中さん2018/11/16(金) 20:36:06.68ID:UpzDESQt てか、Core0 Panicってどうなってんの? 使ってねぇぞ。 xTaskCreatePinnedToCoreは・・・ 0512774ワット発電中さん2018/11/17(土) 00:08:47.07ID:dpf2nccD 毎回19028回なら ソフト臭いね 0513774ワット発電中さん2018/11/17(土) 04:58:54.81ID:lRhDTRDW 単につなぎに行って帰ってこないということなら、ルータのNATあふれとか他の原因も 疑うけれど 0514774ワット発電中さん2018/11/17(土) 12:58:11.03ID:h7CQDigb 単純にclient.stop使ってないとかそのあたりかね 0515774ワット発電中さん2018/11/17(土) 13:15:26.50ID:yS6jweg+ 海外でESP8266でPC-XTのエミュ作ったと。 Ichigo Jamの互換機くらい作れるなw 0516774ワット発電中さん2018/11/17(土) 18:33:01.19ID:jZ52th6p MSXエミュに挑戦するんや 0517774ワット発電中さん2018/11/17(土) 19:25:12.43ID:GvrVdEL0 そういうのってFPGAでやるんじゃないの? 0518774ワット発電中さん2018/11/19(月) 12:55:16.52ID:yWYqF97p DebugMode を Debug にしてると思うけど「なし」でも試してみるよろし 違いがあれば、>>508 の可能性 0519774ワット発電中さん2018/11/22(木) 22:07:26.47ID:QfskCBHL obniz は、成功するんだろうか? 0520774ワット発電中さん2018/11/23(金) 19:20:35.43ID:2bYV40kG ESP32でI2Cバス二つとタイマーを同時に使えてる方いませんか? 0521774ワット発電中さん2018/11/23(金) 19:43:43.27ID:9N8DlNW7 います! 0522774ワット発電中さん2018/11/27(火) 03:51:16.23ID:VnMhs82S Advent Calendarの季節だよもん 0523774ワット発電中さん2018/11/27(火) 13:37:34.58ID:redI3h3R esp32 100k〜1MSPSの外部AD使えるのか?
I recently got a task to do using the AD7767 128 kSPS 24-bit ADC. で So, I should be getting around 46 ksps. However, practically I only get around 22ksps しかでてないらしい。 esp32の限界スペックが知りたいのだが 24bitバッファ問題で12bitだと1Mspsでるかな?
Meanwhile, using an ESP32 board that I have, I've tried using the internal 4MB flash memory (GD25Q32C) that's hooked up on the SPI interface to store ADC data @32ksps (I've used a slower ADC) and.... success. :) It works with 128ksps too. SPI接続4MBフラッシュに格納すれば128kspsも成功と(その後バッファあふれて止まるらしい)
限界スペックと言った時には、とにかく I2S なんでもかんでも I2S だよ。 0525774ワット発電中さん2018/11/28(水) 17:08:22.20ID:xlBtz/0e Meanwhile, using an ESP32 board that I have, I've tried using the internal 4MB flash memory (GD25Q32C) that's hooked up on the SPI interface to store ADC data @32ksps (I've used a slower ADC) and.... success. :) Down bellow you'll find the graph. It does correspond to the action that I was performing on the load cell (3 compressions in a row). It works with 128ksps too.